• /// x-108.com in a new style
    /// After more than 4 years it was time to update the forum to the latest version. We also decided on a new design...

X-108 Info Settings gelöscht? So erarbeitet man diese (1 Viewer)

hb9eue

Junior Boarder
X-108 Member
Registriert
25 Mai 2015
Beiträge
8
Punkte Reaktionen
6
Punkte
3
Alter
52
Lieber OM

  • Du hattest einen Rechner via USB am X108 angeschlossen und diesen in den Software Update Modus geschaltet
  • Der Rechner hat auf das Memory des X108 zugegriffen und die Firmware abgeschossen
  • Du hast erfolgreich wieder eine laufende Firmware geflasht
  • Nun stimmen die Angaben über IF und BFO Frequenzen nicht mehr, da die Default Werte geladen wurden, der TRX ist so gut wie taub.
  • Du hattest die Einstellungen nirgendwo notiert.
Genau dies ist mir geschehen, und mit etwas tüfteln, habe ich einen Weg gefunden, diese wieder hinzukriegen. Dazu müsste Du Deinen TRX aufschrauben. Bei meinem ist sowohl auf der Hauptplatine wie auch auf den Quarzen ein Aufkleber mit den IF Frequenzen für USB und CW zu finden. Also wohl die Frequenz des 500Hz und des 2.3kHz Filters.

Diese dort dokumentierten Frequenzen überträgst Du in die Einstellung von USB und CW IF Frequency. Notiere die Default Werte!

Dann berechnest Du das Delta zwischen den IF Frequenzen auf der Platine und den vorher dort stehenden Default Werten.

Dieses Delta wendest Du auch bei den BFO Frequenzen an.
Nun bist Du in der Nähe der korrekten Frequenzen und der TRX sollte zumindest wieder etwas hören, wenn auch mit klar abgeschnittenen Höhen oder Tiefen. Nun diese Frequenzen nach oben oder unten korrigieren, bis sich das Audio wieder korrekt anhört. Ich musste um ca. 1.2kHz korrigieren.

73. de HB9EUE
 
Zuletzt bearbeitet:

X-Boarder

Crack-Boarder
X-108 Member
Registriert
16 Januar 2015
Beiträge
27
Punkte Reaktionen
8
Punkte
3
Alter
58
Verified User
YES
i found this note on yahoo group:

backup firmware.bin BEFORE updating.

This doesn´t make any sense because you can´t use this file to restore your radio! Don´t try this without a real firmware file (*.xgf) because you will get a radio with just a black screen. Only the green power light will be on... Tried this myself and could get my X108 go back to life only by using the *.xgf file! In the past each up- and downgrading the firmware to other releases would work, but not with the*.bin file.

Beware!
 
Zuletzt bearbeitet von einem Moderator:

shortwave

Beginner
X-108 Member
Member pro !
Registriert
6 Januar 2015
Beiträge
5
Punkte Reaktionen
0
Punkte
1
Alter
47
Verified User
NO
i found also this note on yahoo group:

Thanks for that info this is the reason we asked Xiegu for the standard firmware so if this does happen to you the file needed to restore it is now in the file section here ...

Something else worth noting is that also observed that reinstalling the firmware did not effect his IF and BFO settings at all. This is a good thing but we still need to keep our IF and BFO settings for reference to resolve the RST function..

Hopefully a fix will come where this will no longer happen, i think it is still a bug in the firmware because the first and second batch sets all settings for the IF &BFO went to Zeros ..

I have noted on mine this now only alters them slightly and is far quicker to put right with the correct settings...I think menu 11 should also be done so it stays on a zero and not a one after again the RST is used.. It appears to be of no value by this changing and just adds further confusion and upset for those that are not aware of it...These tiny niggles will hopefully be resolved in future firmware updates..
 
Zuletzt bearbeitet von einem Moderator:

X-108

Crack-Boarder
Teammitglied
X-108 Member
SITE-MOD
Registriert
17 Januar 2015
Beiträge
27
Punkte Reaktionen
19
Punkte
3
Alter
54
Ort
Stuttgart
Website
www.x-108.com
Verified User
YES
admin submitted a new resource:

Firmware Update X108_FW_V1.35.1_Build0150 - x-108 Firmware V 1.35.1 Build 0150

Firmware Update X108_FW_V1.35.1_Build0150

Release Date: 2015/3/3 22:07:03

Read more about this resource...

WARNUNG: Die auf der cqxiegu.com angebotene Firmware
X108_FW_V1.35.1_Build0150 funktioniert, zumindest auf meinem TRX (Serial: XG00110) nicht. In der Anleitung findet sich der Hinweis, dass die Firmware eine bestimmte Hardware Version voraussetzt.
 
Zuletzt bearbeitet von einem Moderator:

DO7PSL

Crack-Boarder
Teammitglied
X-108 Member
Registriert
30 November 2014
Beiträge
100
Punkte Reaktionen
6
Punkte
1.008
Ort
Stuttgart
Country
de
Website
do7psl.de
Verified User
YES
Rufzeichen/Call
DO7PSL
How to restore youre Xiegu X108G after a RST reset

You must be registered for see medias
 

DO7PSL

Crack-Boarder
Teammitglied
X-108 Member
Registriert
30 November 2014
Beiträge
100
Punkte Reaktionen
6
Punkte
1.008
Ort
Stuttgart
Country
de
Website
do7psl.de
Verified User
YES
Rufzeichen/Call
DO7PSL
Meine Vorgehensweise:

Gerät öffnen und prüfen was auf den Labels steht. In meinem Fall Stand folgendes:

SSB 10692620 Hz
CW 10692390 Hz


der Offset beträgt 1100 Hz. Dies konnte ich u.a. erkennen, als ich meinen x-108G öffnete, die Labels und anschliessend die advanced settings prüfte (press and hold F1 button while powering on). So konnte ich sichergehen, dass der Offset auch 1100 Hz beträgt. Nach dem reset habe ich dann die Werte in den advanced settings eingetragen - Details siehe Attachment

that´s it Wtf

Hier noch die Firmware welche ich für den x-108 STANDARD verwendet habe:

---------------------------------------------------------------

My approach:

Open the unit and check what is written on the label. In my case, the following status:

SSB 10692620 Hz
CW 10692390 Hz


the offset is 1100 Hz. This is what I could see, among other things, when I opened my x-108G, the label and then the advanced settings checked (press and hold F1 button while powering on). So I could be sure that the offset is also 1100 Hz. After the reset, I then entered the values in the advanced settings - for details, see Attachment

That's it Wtf
---------------------------------------------------------------

Here the firmware which I have used for the x-108 STANDARD:

admin submitted a new resource:

Latest Firmware xiegu x-108 (STANDARD, 2nd batch) 1.35.1 - Latest Firmware xiegu x-108 (STANDARD, 2nd batch) 1.35.1

Latest Firmware xiegu x-108 (STANDARD, 2nd batch) - V-1.35.1

Read more about this resource...
 

Anhänge

  • xiegu-x108standard-advanced-settings.pdf
    55,8 KB · Aufrufe: 56
  • xiegu-x108standard-advanced-settings.xlsx
    42 KB · Aufrufe: 35
Zuletzt bearbeitet von einem Moderator:

X-108

Crack-Boarder
Teammitglied
X-108 Member
SITE-MOD
Registriert
17 Januar 2015
Beiträge
27
Punkte Reaktionen
19
Punkte
3
Alter
54
Ort
Stuttgart
Website
www.x-108.com
Verified User
YES
update instruction:
  • Firmware update tutorial:
    1. Press the frequency knob (keep the action), turn on, connect the
      USB cable to the computer.
    2. Open “ My computer”, there is a Update X108 mobile
      storage device.
    3. Open Update X108 (*), delete the file (firmware.bin), this time on the radio will show delete progress (waiting for progress to complete 100%).
    4. Copy the latest firmware (X108_FW_V1.35.1_PHYSPTT.xgf) to the Update X108 to wait for
      replication to complete, and then disconnect the USB and the
      computer.
    5. Restart X108G, firmware update is completed!
    6. that´s it :rolleyes:
 

admin

Administrator
Teammitglied
X-108 Member
SITE-ADMIN
SITE-MOD
Registriert
30 November 2014
Beiträge
113
Punkte Reaktionen
64
Punkte
1.027
Ort
Stuttgart
Country
de
Website
do7psl.de
Verified User
YES
Rufzeichen/Call
noCall
press power on and F2 - is the radio calibrate menu - here my factory settings for the xiegu x-108 outdoor
 

Anhänge

  • xiegu-108-otdoor-radio-calibrate-settings.JPG
    xiegu-108-otdoor-radio-calibrate-settings.JPG
    153,4 KB · Aufrufe: 96

kwitt

Beginner
X-108 Member
Registriert
5 Juni 2016
Beiträge
2
Punkte Reaktionen
0
Punkte
1
Alter
34
Verified User
YES
Rufzeichen/Call
DL6LAT
admin submitted a new resource:

Firmware Update X108_FW_V1.35.1_Build0150 - x-108 Firmware V 1.35.1 Build 0150



Read more about this resource...

WARNUNG: Die auf der cqxiegu.com angebotene Firmware
X108_FW_V1.35.1_Build0150 funktioniert, zumindest auf meinem TRX (Serial: XG00110) nicht. In der Anleitung findet sich der Hinweis, dass die Firmware eine bestimmte Hardware Version voraussetzt.

i found this note on yahoo group:
Mist, zu spät.
Dabei wollte ich nur ein Backup vom X-108 anlegen.
 

Users who are viewing this thread

Oben
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock    No Thanks