Xiegu X108G Outdoor version standard PTT out procedure. Check this procedure if you want to add a standard PTT out for your linear amplifier.
december 2016 1.00.04 firmware for an x108g outdoor with CXG 10xxx serial number remember to first backup your settings power on+press F1 and write down everythung. I would do the same thing with power on+press F2 Only then update the firmware
Hat jemand eine Anleitung, wie ich das Gerät X108G am besten auseinander bauen kann? Würde gerne die tx Erweiterung basteln .. VY 73
Hello all. I have an issue that I am sure is something that I did with the firmware. Radio was working, then I updated to v2.00.1_build002 and I dont hear anything. SQL is 0, so its not that.. my antenna is good, I am using it on my IC7300 with out issue. I use this little guy for camping, but I think its dead now. I got all my numbers, put them in and no joy. I could have screwed something up... hard to tell. I have tried downgrading, and upgrading.. no joy for sound. display comes on, looks good. Thanks for reading this.
Good day! After upgrading to version 1.00.4, the sound became quiet, and the stations are not listening. Settings F1 correspond to the saved. Tell me how to return the sound?
one firmware gives me a display but no sound,,other firmware gives me a blank screen....my rig is 01 serial number,i got that part right..i do a lot on computers at work.....i am not out tho,,.i paid 100 bucks for this at a fleemarket..knowing the transmitt section was out..all should note where you order mosfets ,the finals..one company off ebay that sells replacement mosfets , thay are bigger than orig ones...may try to contact somone from mfg...but dont have a lot of hopes..
Hi im new here. Just got my X108G outdoor radio. It has the FW v1.00.4 May 2017. The radio does not RX or TX, do anyone have suggestions of what to do?
Hi new here just got my x108g and AM swings in reverse can anyone help with the outdoor version, the AM reverse modulation? How do i reverse this crime against AM opperation? Thanks in advance for any info at all. 73s hope to hear these radios on the air.
Thay probley all do that..mine also .i also noticed the noise blanket don't work at all...i have a parts radio now...i have used AM on 10 meter and even with backwards swing have got good reports..if ya put a peak reading watt meter on you will have forward swing..best73
Finaly got a mail from xiegu. They said to open the radio and check if the antenna connector is is broken(bad solder). The antenna connector is just fine, no bad solder or anything. Since i allready had open the radio, i traced the signal through bpf's to the mixer. I seems like there is no local oscillator signal to the mixer? The TCXO works fine, strong 26MHz signal. Is there anybody that have the new outdoor version 0,5ppm 26MHz TCXO that have the same problem?
[QUOTE = "wgoodf, publicación: 443, miembro: 88"] Hola chicos - Acabo de registrarme como tengo un X108G bloqueado. Estaba teniendo un extraño problema de software: la radio se bloqueaba cuando presionaba el botón para dividir el trabajo y, a veces, giraba la perilla y la frecuencia seguía cambiando después de retirar mi mano. De todos modos, contacté a Xiegu y me enviaron el archivo V1 build 24. Lo instalé como las instrucciones y ahora la radio está bloqueada con una pantalla blanca. El proceso que utilicé fue este: Conecto la radio a la computadora. He probado Windows XP y MacOS. Sostengo el botón y enciendo; llego a la pantalla de actualización. La radio se monta como E: - Elimino el archivo firmware.bin. La radio flash se borra al 100% = Flash Erase OK Copio el archivo: X108G_OLED_FW_V1.00_build024.xgf - a la radio. (he probado otros y solo he intentado el V2 build10.) Escritura flash - 137728 bytes - ¡Actualización realizada! Por favor reinicie su plataforma. Apago el equipo: desconecto el USB de la computadora, enciendo el equipo y la pantalla está blanca, sin pitido de arranque. La pequeña luz verde en el puerto del micrófono está encendida. Eso es todo lo que hace: la radio ahora está muerta. ¿Me estoy perdiendo algo o estoy haciendo algo estúpido? Cualquier ayuda sería muy apreciada. Gracias por adelantado. wgoodf / MM6FXZ [/ QUOTE] Hola saludos cordiales desde lima Perú! Después de quitar la actualización tienes que apagar el equipo,quitar el cable de voltaje encender el equipo sin el cable para ir descargues todo el voltaje que se almacena en el, luego lo apagas y le vuelves. Conectar el cable de voltaje y encenderlo nuevamente y listo regresa a la vida! Saludos cordiales OA4LDR
[QUOTE = "Jabier, post: 1072, member: 905"] ¿Cómo es posible ver el número de serie? Es posible: CXG0026 ... [/ QUOTE] Esta es mi serie !!! Y le puse está actualización del x108g v2 y el menú de servicio F1 es de 15 ítems y el menú F2 queda de esta manera se la imagen! ¡Y removí R76 que en mi modelo no lo dije y abrí los 11 metros! Aprovechar en cambiar la pila de la memoria también! Voy a seguir experimentando y les voy informando de las novedades! Voy a tratar de subir el firmware del 2017! Saludos cordiales desde Lima-Peru OA4LDR 73s